HOME › SERVICES › GUTTER INSTALLATION
Gutter Installation Across The Greater Toronto Area
Either a gutter system catches what a storm deposits on your roof or it doesn’t. That’s determined before they reach for a ladder. Width, downspout size, slope, distance between hangers and the ultimate destination of the water are all determined at the planning stage. Get those wrong and no amount of careful fitting will save it. Roofing Repairs Dun-Rite Inc. determines the size of the system based on the roof surface area that it is serving, and constructs it to remain straight through Ontario winters.
01
Seamless Gutter Installation Built To Outlast Ontario Winters
We do not join short lengths of gutters together, but manufacture seamless aluminium gutters on-site to match the exact length of your roof line. It’s for one reason: Each joint is a weak point, and Ontario winters are harsh at joints. Water freezes, expands, and the sealant at those joints gradually wears away to allow gaps to form and water drains down behind the gutter onto the fascia. A seamless run will only have joints at the corners and the downspouts which will be sealed by proper joints. Less joints equals less room to break. Over a period of more than 10 years, across a long roofline. When forming we match the colour to your fascia and trim.
02
Affordable Vinyl Gutter Installation That Holds Its Line For Years
If budget is a major concern, and the roofline is relatively straightforward, we use vinyl. But today’s vinyl holds up much better against sun and cold than vinyl products of years gone by that had earned a bad reputation. The spacing of hangers determines whether it lasts or not. The fewer hangers used, the faster and less expensive it is, and the gutter will sag in a few years between hangers. When it sags it retains water, gathers trash and goes out of alignment. Space hangers are used to straighten run its entire length, slope, and seal joints. We let you know that Vinyl won’t last as long as Aluminium.
03
Expert Gutter Guard Installation Matched To Your Property's Debris
Guards are selected on the basis of what is really falling on your roof. If mature trees are overhanging the house, we generally recommend micro-mesh as it will exclude the largest amount of leaves and debris. Surface tension and reverse-curve guards work great in some cases and not so great with fine material such as pine needles, seed pods and the fine grit that falls off aged shingles. Both your gutter shape and budget factor in. We also explain up front that guards do not reduce the cleaning frequency to nothing; fine debris does get through and the guards themselves must be cleaned at some time.
How Is Gutter Size Calculated For Your Roof Area?
We determine gutter size based on the roof that drains to each section and not from whatever is already there. A large roof plane connected to a short gutter must contain a lot more than a short gutter connected to a small wall. Roof pitch also is important since a steeper roof will move water down the roof quicker. The size and the number of downspouts are given by the same numbers. We design for heavy rain not average rain, a gutter that will hold up just fine most of the time and overflows during each rain is failing when it counts.
Why Does Gutter Slope Decide Whether The System Drains?
A gutter is a channel, not a bucket. It only works as long as water keeps flowing toward the downspout. If it is not steep enough, water will pool in the low spots and debris will not wash out and the metal will begin to corrode from the inside. An excessive angle looks wrong against the fascia and, during heavy rain, can cause water to run right through the downspout inlet. Fall section by section each run (even). This is most important on long walls, where a small mistake at the end will be a large error at the opposite end.
What Holds A Gutter System Through Ice Loading?
Everything goes on the hangers and fasteners, and it is during the winter months that it is heaviest. When a gutter is full of ice, it weighs a lot more than people think it does, and the system needs to remain straight under the weight of the ice as the metal expands and contracts with each temperature fluctuation. If hangers are placed too far apart, then the gutter sags in between them. After it bends, it retains the water, which freezes and the bend worsens. Fasteners matter just as much. Inexpensive hardware rusts in just a few seasons, it’s not secure in the fascia board, and the gutter begins to come loose at the point where the ice is heaviest.
Where Should Downspouts Discharge To Protect Your Foundation?
Away from the house, which sounds obvious and gets missed all the time. Before we begin, we first determine where the downspouts are going, which determines whether or not the system will protect your building or if it is going to dump all the roof water to the bottom of your wall. A downspout that drains onto soil that is inclined away from the house merely relocates the issue. From damp foundations to water in the basement and washed out garden beds, it all begins here. Extensions and splash blocks are included where necessary and if the ground levels are against drainage, we will let you know.
Should You Replace Gutters And Roof Together?
Usually yes, for practical reasons rather than to sell you more. The drip edge, fascia, soffit and gutter all connect at the same spot along the roof line and when both are installed simultaneously, it is a much easier join to get right. It’s hard to avoid disturbing the gutters when a roof needs repairing, and gutters that are already worn out are likely to break under the stress of the changes. When gutters still have many years of useful life remaining, we say so, and work around them. When both are close to the end, it is better to do together, saving both money and neatness.
What Makes A Gutter Installation Last Twenty Years?
Plenty of installers match whatever was there, hang it quickly, use the fewest hangers they can and leave. The gutter leaks in its first storm and slides down the hill quicker than it should. Before anything is ordered, Roofing Repairs Dun-Rite Inc. determines the square footage of the roof, calculates the slope per section, installs hangers within an acceptable distance of the line of water, speculates for the appropriate hardware that will endure a GTA winter and the discharge location of the water. Brad Ellis inspects the fasteners and does a walk of the completed work prior to leaving.
Gutter Installation Across Toronto And Durham Region
Most of our gutter work is from North York, and the surrounding areas of Etobicoke, East York and Scarborough. Consequently, we frequently install gutters with a roof replacement in Markham, Richmond Hill and Thornhill. We service Pickering, Ajax and Oshawa, where hanging locations closer to the lake are more critical than in the other areas of Durham Region due to their proximity to the lake and exposed conditions. No subcontracting is done anywhere in the service area.
Etobicoke
North York
East York
Scarborough
Markham
Richmond Hill
Thornhill
Pickering
Ajax
Oshawa
Mississauga
Get Your Roofline Measured And Specified
Describe the type of property, approximate age of existing gutters and if gutters overflow during heavy rains. Before anything is ordered, we will measure the roof areas for each run, calculate the actual size of the system, and quote the entire job, without extra charges for water discharge locations.